OSEC

Neohapsis is currently accepting applications for employment. For more information, please visit our website www.neohapsis.com or email hr@neohapsis.com
 
From: fad (fadfad.homeip.net)
Date: Fri Dec 07 2001 - 17:20:54 CST

  • Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

    I just thought i would share my experiences with a compaq wl110, and a
    cardbus TI pci adapter,
    the adapter worked fine in linux 2.2.18pre21, however i couldnt get anything
    to compile, i tried orinoco-0.08b and the lucent half binary drivers.
    After alot of stuffing around i installed 2.4.12 kernel, which was a bit
    involoved,
    along with pcmcia-cs 3.1.15 and wireless tools 22,

    These were in my apt /etc/apt/sources.list file

    deb http://people.debian.org/~bunk/debian potato main
    deb-src http://people.debian.org/~bunk/debian potato main

    They allow an upgrade to 2.4 from 2.2 all you need it a apt-get update
    apt-get upgrade,
    there are some packages which die in 2.4 like ppp and ipmasq, this will fix
    it, you also need to upgrade a libc.
    Anyway after getting the kernel to work, remember to set the required kernel
    options on the compile,
    (kernels at www.kernels.org)
    compile and install the pcmcia-cs and wireless tools, there should be
    drivers in your kernel, if you compile them, else get the orinoco-0.08b
    drivers.

    if you can insmod the orinoco_cs.o , where you first load hermes.o and
    orinoco.o first, then your card is there.
    you will need to now set some options into /etc/pcmcia

    there are examples for /etc/pcmcia/wireless.opts

    I had to add this to the /etc/pcmcia/hermes.conf, my compaq card was first
    undetected as unknown, and then as a prism II card, which is fine but the
    driver was wvlan_cs.o, and i wanted orinoco_cs.o
    so i editied it with

    --
    # First class of device : Lucent & OEM
    card "Orinoco or Intersil Prism 2 Wireless"
      manfid 0x0156,0x0002
      bind "orinoco_cs"
    

    finally all you need to do is set /etc/pcmcia/wireless.opts and network.opts

    and as a result i now have a wireless card, :)) I found it very hard to find information on this, about why i needed to upgrade and why the drivers which were back ported wouldnt work in 2.2.18 so this might help someone, -fad

    ifconfig eth0 Link encap:Ethernet HWaddr 00:10:4B:2F:E1:81 inet addr:10.0.0.1 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:2991013 errors:0 dropped:0 overruns:0 frame:0 TX packets:3480055 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:11 Base address:0xde00

    eth1 Link encap:Ethernet HWaddr 00:02:A5:6E:62:12 inet addr:10.0.1.1 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33472 errors:0 dropped:0 overruns:0 frame:0 TX packets:48983 errors:4 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 Interrupt:5 Base address:0x100 iwconfig eth1 IEEE 802.11-DS ESSID:"my network" Nickname:"router" Mode:Ad-Hoc Frequency:2.457GHz Cell: 02:02:A5:6E:62:12 Bit Rate:11Mb/s Tx-Power=15 dBm Sensitivity:1/3 Retry limit:4 RTS thr:off Fragment thr:off Encryption key:off Power Management:off

    ---------------------------------------------------------------------------- ----------- its nice to be important but its more important to be nice

    ------------------------------------- fad.homeip.net