|
Neohapsis is currently accepting applications for employment. For more information, please visit our website www.neohapsis.com or email hr@neohapsis.com |
all firmware patch digest
From: IT Resource Center (support_feedback
us-support2-mail.external.hp.com)
Date: Sun Jun 29 2003 - 06:19:35 CDT
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
HP Support Information Digests
===============================================================================
o IT Resource Center World Wide Web Service
---------------------------------------------------
If you subscribed through the IT Resource Center and would
like to be REMOVED from this mailing list, access the
IT Resource Center on the World Wide Web at:
http://support.itrc.hp.com/
Login using your IT Resource Center User ID and Password.
Then select Support Information Digests (located under
Maintenance and Support). You may then unsubscribe from the
appropriate digest.
To download a patch referenced below, access the
IT Resource Center on the World Wide Web at:
http://support.itrc.hp.com/
Login using your IT Resource Center User ID and Password.
Then select Individual Patches (under Maintenance and Support)
to access the patch. You may also download a patch via anonymous
ftp(1) from ftp.itrc.hp.com.
===============================================================================
Digest Name: weekly all firmware patch digest
Created: Sun Jun 29 6:05:01 EDT 2003
Table of Contents:
Document ID Title
--------------- -----------
PF_CCJ70020 C3650/C3700/C3750/J6700/J6750 firmware 2.0 patch
The documents are listed below.
-------------------------------------------------------------------------------
Document ID: PF_CCJ70020
Date Loaded: 20030626
Title: C3650/C3700/C3750/J6700/J6750 firmware 2.0 patch
Patch Name: PF_CCJ70020
Patch Description: C3650/C3700/C3750/J6700/J6750 firmware 2.0 patch
Creation Date: 03/06/24
Post Date: 03/06/26
Products:
9000/785/C3650
8000/785/C3700
9000/785/C3750
9000/785/J6700
9000/785/J6750
Status: General Release
Critical: No
Category Tags:
defect_repair hardware_enablement general_release firmware
Path Name: /firmware_patches/hp/cpu/PF_CCJ70020
Symptoms:
PF_CCJ70020:
Traps
- Data cache tag LPMC no longer generates an "Unaligned
data reference" trap.
Ten LPMCs are logged, then LPMCs are disabled.
I/O
- The firmware delays the proper amount of time after a
PCI bus reset as specified by the PCI spec. The delay is
1 second for a 33Mhz PCI bus and .5 seconds for a 66Mhz
PCI bus.
IODC
- Enabled SCSI IODC for the Symbios Logic SYM531010
chip. The following Ultra 160 PCI option cards were
tested: A6828-60001 and A6829-60001.
Defect Description:
PF_CCJ70020:
Firmware revision required.
Enhancement:
No
SR:
0000000000
Patch Files:
PF_CCJ70020.frm
cksum(1) Output:
3958484385 3465216 PF_CCJ70020.frm
Patch Conflicts: None
Patch Dependencies: None
Hardware Dependencies:
9000/785/C3650
8000/785/C3700
9000/785/C3750
9000/785/J6700
9000/785/J6750
Other Dependencies: None
Supersedes: None
Equivalent Patches: None
Patch Package Size: 3332 KBytes
Installation Instructions:
Please review all instructions and the "Hewlett-Packard
Support Tool License Terms" or your Hewlett-Packard support
terms and conditions for precautions, scope of license,
restrictions, and, limitation of liability and warranties,
before installing this patch.
PLEASE BACK UP YOUR SYSTEM BEFORE YOU INSTALL THE PATCH.
NOTE: It is important that you read and understand these
instructions completely before you begin. This can
determine your success in completing the Firmware update.
Be sure to prepare the system and its users before
beginning a Firmware update. Since the system will not be
in operation during the update, you should notify
appropriate managers and users as to when it will be
shutdown and for how long it will remain inoperative.
The Firmware update should take no longer than 30 minutes
to complete.
* * * * * * * * VERIFYING CURRENT REVISION OF FIRMWARE * * * * * * * *
VERIFYING FIRMWARE REVISION WITH ON-LINE DIAGNOSTICS
The current revision of Firmware can be determined using on-line
diagnostics. If on-line diagnostics are not present on your
system, use the BOOT CONSOLE HANDLER procedure to verify the
current revision.
Procedure for all systems
1. Login as root
2. At the prompt, enter 'mstm'
3. Press f2 (ok)
4. Move the cursor to "CPU"
5. Press f3 (select)
6. Press f4 (menu bar on)
7. Enter "T" to select Tool Menu
8. Enter "I" to select Information Mode
9. Enter "R" to Run
After a few seconds, the Information Tool Log for
the CPU will be displayed. The 'PDC Firmware
Revision' is displayed in the first column.
10. Note the PDC Firmware value
11. Press f8 (done)
12. Press f8 (exit)
13. Press f2 (ok)
If the revision is not 2.0, your system will require
a Firmware update. Skip the next section, and follow the
instructions for CREATING THE FIRMWARE UPDATE TAPE.
VERIFYING FIRMWARE REVISION WITH BOOT CONSOLE HANDLER (BCH)
1. Log on as root, and enter "shutdown -r". This command
will shutdown the Operating System and reboot the system.
2. If AUTOBOOT is on, you will receive the following message:
"Process is starting autoboot process
To discontinue, press any key within 10 seconds."
At this point, press ANY KEY within 10 seconds to
interrupt the booting process.
3. The Main Menu is displayed. A prompt will appear as
"MAIN MENU: Enter command or menu>".
Enter the command "in".
4. A prompt will appear as "Information Menu: Enter Command>"
Enter the command "fv"
The system will respond with the current firmware
revision. If the revision is not revision 2.0
your system will require a Firmware update. Follow the
instructions in the next section, CREATING THE FIRMWARE
UPDATE TAPE.
* * * * * * * * * * CREATING THE FIRMWARE UPDATE TAPE * * * * * * * *
1. Verify the checksum of the file "PF_CCJ70020.frm" using
the "sum" command. Results of the command should be
equal to "48138 6624 PF_CCJ70020.frm".
2. Use the "dd" command to copy the file "PF_CCJ70020.frm"
to tape, as follows:
dd if=PF_CCJ70020.frm of=/dev/rmt/0m bs=2k
^^^^^^^^^^^
(device path dependent)
NOTE: Blocksize (bs) must be 2k
* * * * * * * * * * * FIRMWARE UPDATE PROCEDURE * * * * * * * * * * *
NOTE: ENSURE YOUR SYSTEM IS FULLY BACKED UP BEFORE
PROCEEDING WITH THIS FIRMWARE UPDATE.
1. Log on as root, and enter "shutdown -r". This command
will shutdown the Operating System and reboot the system.
2. If AUTOBOOT is on, you will receive the following
message:
"Process is starting autoboot process
To discontinue, press any key within 10 seconds."
PRESS ANY KEY WITHIN 10 SECONDS TO INTERRUPT
THE BOOTING PROCESS.
3. Boot from the device that contains the firmware update tape
you just created.
4. Interact with IPL (Y or N)?>
Respond with "N".
A series of messages will be displayed. No user
intervention is required. Proceed to step 5.
5. A message will be displayed as follows:
"F/W file Note:"
"C3650/C3700/C3750/J6700/J6750 PDC firmware image, Version 2.0"
"Continue ([y]/n)?"
Enter "y".
CAUTION: FROM THIS POINT FORWARD, THIS PROCESS CANNOT
BE INTERRUPTED UNTIL COMPLETION. INTERRUPTING
THIS PROCESS WILL CAUSE YOUR SYSTEM TO BE
INOPERATIVE.
6. The update should take approximately two minutes.
After the tape has been read by the update
program, a message will be displayed as follows:
"Firmware downloaded SUCCESSFULLY!"
THIS UTILITY WILL NOW RESET THE SYSTEM....
7. The system will automatically reset, and the boot
process will begin. Boot your system with your
normal process.
If there is a problem with your system after the
update, please contact your service representative.
* * * * * * * * * * * * * * END OF UPDATE * * * * * * * * * * * * * *
-----End of Document ID: PF_CCJ70020-----------------------------------------
- Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]