From: Stefan Kell (skba.opbsdgmx.de)
Date: Tue Jan 04 2005 - 07:52:03 CST

• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hello,

I am not a MAC-specialist, but: from the installation instructions at
"ftp://ftp.openbsd.org/pub/OpenBSD/3.6/macppc/INSTALL.macppc"

>> Autobooting OpenBSD/macppc
>>
>>
>> It is possible to automatically boot into OpenBSD (selectably into Mac
>> OS) by setting up the following:
>>
>> setenv auto-boot? true
>> setenv boot-device hd:,ofwboot
>>
>> [to save the results into NVRAM]
>> reset-all
>>
>> These settings assume that the master of the first IDE bus has OpenBSD
>> installed on it, either in MBR format or in shared mode with ofwboot
>> copied into the first HFS(+) partition. It is not necessary to specify
>> '/bsd' on the boot line or in the boot-device variable, since it is the
>> default.

if hd: and cd: are have been swapped (as is shown in your dmesg) you
could try "setenv boot-device cd:,ofwboot".

Regards

Stefan

On Tue, 4 Jan 2005, David Clarke wrote:

> Hi
>
> I've installed 3.6 on an Apple Cube, intending to run it headless as a
> development server (nice and quiet to keep my family happy). The
> cube has been modded by the previous owner including a
> processor card upgrade. The mod that appears to be giving me
> grief is the 3rd-party DVD writer. There appears to have been some
> jiggery pokery involved in the installation and the Open Firmware
> aliases for hd & cd are reversed (which means eject hd: actually
> ejects the cd). Apart from my usual wrestle with disklabel & fdisk,
> the install was fine but as you can see in dmesg below, I have to
> specify where the root device is. I could just about live with this but
> I really want to run it headless. I've googled but haven't been able
> to locate anything particularly useful.
>
> Any help would be appreciated.
>
> Thanks
> Dave
>
> [ using 373324 bytes of bsd ELF symbol table ]
> console out [ATY,Rage128Pd]console in [keyboard] USB found
> : memaddr 94000000 size 4000000, : consaddr 96008000, : ioaddr
> 90020000, size 20000: memtag 8000, iotag 8000: width 640 linebytes 768
> height 480 depth 8
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
> Copyright (c) 1995-2004 OpenBSD. All rights reserved. http://www.OpenBSD.org
>
> OpenBSD 3.6 (GENERIC) #47: Fri Sep 17 14:55:19 MDT 2004
> deraadtmacppc.openbsd.org:/usr/src/sys/arch/macppc/compile/GENERIC
> real mem = 129826816 (126784K)
> avail mem = 113201152 (110548K)
> using 1254 buffers containing 6488064 bytes of memory
> mainbus0 (root)
> cpu0 at mainbus0: 7455 (Revision 303): 1200 MHz: 256KB L2 cache, 2MB L3 cache
> memc0 at mainbus0: uni-n
> mpcpcibr0 at mainbus0: uni-north, Revision 0xff
> pci0 at mpcpcibr0 bus 0
> pchb0 at pci0 dev 11 function 0 "Apple Uni-N AGP" rev 0x00
> vgafb0 at pci0 dev 16 function 0 "ATI Rage Fury" rev 0x00, mmio
> wsdisplay0 at vgafb0: console (std, vt100 emulation)
> mpcpcibr1 at mainbus0: uni-north, Revision 0x16
> pci1 at mpcpcibr1 bus 0
> pchb1 at pci1 dev 11 function 0 "Apple Uni-N" rev 0x00
> macobio0 at pci1 dev 23 function 0 "Apple Keylargo" rev 0x03
> openpic0 at macobio0: version 0x4614
> gpio_obio0 at macobio0
> gpio_obio1 at gpio_obio0 irq 47
> programmer-switch at gpio_obio0 not configured
> zsc0 at macobio0: irq 22,50
> zstty0 at zsc0 channel 0
> zstty1 at zsc0 channel 1
> adb0 at macobio0 irq 25: via-pmu 0 targets
> aed0 at adb0 addr 0: ADB Event device
> apm0 at adb0: battery flags 0x9, 0% charged
> ki2c0 at macobio0
> wdc0 at macobio0 irq 19: DMA
> atapiscsi0 at wdc0 channel 0 drive 0
> scsibus0 at atapiscsi0: 2 targets
> cd0 at scsibus0 targ 0 lun 0: <MATSHITA, DVD-R UJ-815, DWDB> SCSI0
> 5/cdrom removable
> wd0 at wdc0 channel 0 drive 1: <ST360015A>
> wd0: 16-sector PIO, LBA, 57241MB, 117231408 sectors
> cd0(wdc0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 4
> wd0(wdc0:0:1): using PIO mode 4, DMA mode 2, Ultra-DMA mode 4
> wdc1 at macobio0 irq 20: DMA
> wdc2 at macobio0 irq 21: DMA
> ohci0 at pci1 dev 24 function 0 "Apple USB" rev 0x00: irq 27, version 1.0
> usb0 at ohci0: USB revision 1.0
> uhub0 at usb0
> uhub0: Apple OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uhub1 at uhub0 port 1
> uhub1: Mitsumi Electric Hub in Apple Extended USB Keyboard, class 9/0,
> rev 1.10/1.22, addr 2
> uhub1: 3 ports with 2 removable, bus powered
> uhidev0 at uhub1 port 1 configuration 1 interface 0
> uhidev0: Mitsumi Electric Apple Extended USB Keyboard, rev 1.10/1.22,
> addr 3, iclass 3/1
> ukbd0 at uhidev0: 8 modifier keys, 6 key codes
> wskbd0 at ukbd0 (mux 1 ignored for console): console keyboard, using wsdisplay0
> uhidev1 at uhub1 port 1 configuration 1 interface 1
> uhidev1: Mitsumi Electric Apple Extended USB Keyboard, rev 1.10/1.22,
> addr 3, iclass 3/0
> uhidev1: 3 report ids
> uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
> uhid1 at uhidev1 reportid 3: input=3, output=0, feature=0
> ohci1 at pci1 dev 25 function 0 "Apple USB" rev 0x00: irq 28, version 1.0
> usb1 at ohci1: USB revision 1.0
> uhub2 at usb1
> uhub2: Apple OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub2: 2 ports with 2 removable, self powered
> "Texas Instruments TSB12LV26 FireWire" rev 0x00 at pci1 dev 26
> function 0 not configured
> mpcpcibr2 at mainbus0: uni-north, Revision 0xff
> pci2 at mpcpcibr2 bus 0
> pchb2 at pci2 dev 11 function 0 "Apple Uni-N Eth" rev 0x00
> gem0 at pci2 dev 15 function 0 "Apple GMAC" rev 0x01: irq 41, address
> 00:30:65:ac:0b:62
> lxtphy0 at gem0 phy 0: LXT971 10/100 media interface, rev. 1
> bootpath: '/pcif2000000/mac-io17/ata-41f000/disk1/bsd'
> boot device: lookup 'wd1a' failed.
> root device : wd0a
> swap device (default wd0b):
> root on wd0a
> rootdev=0x0 rrootdev=0xb00 rawdev=0xb02

• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]