From: Srebrenko Sehic (ssehicgmail.com)
Date: Mon May 15 2006 - 01:21:31 CDT

• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Try to disable pcibios. On boot prompt, type:

boot bsd.mp -c
disable pcibios
quit

That might help.

On 5/14/06, Jakub G3azik <zytek-listsostrow-wlkp.net> wrote:
> Hello misc,
>
> I have a problem with booting the MP kernel, it just hangs during boot.
>
> The server is an old big HP NetServer LH II with two P2 300MHz
> processors. It worked very good on Linux with SMP. It's running OpenBSD
> since 3.7 and since then it doesn't boot with GENERIC.MP kernel. GENERIC
> works very fine, no problems at all.
>
> Today I booted into UKC, turned verbose on, but it didn't provided me
> with more info. Last lines during boot are:
>
> >>> probind for isapnp0
> >>> probind for isapnp0 failed
> >>> probind for pcic0
> >>> probind for pcic0 failed
> >>> probind for pcic1
> >>> probind for pcic1 failed
> >>> probind for pcic2
> >>> probind for pcic2 failed
> biosmask 0 netmask 0 ttymask 0
> isapic0: pin 11 shares different IML interrputs (40..50), degraded
> performance
> ^^^^^^^ ^^^
> I'm not sure if these are ok, my "notes" are hard to read, damn ;-)
> I will have serial cable this week so I will be able to dump full text
> from booting.
>
> After that message nothing more happens. I waited for around 4 minutes,
> and then rebooted into GENERIC.
>
> IIRC 3.7 hanged in a different way, on scsi/raid devices.. turning them
> off didn't help a bit. Below is the full dmesg from GENERIC kernel,
> machine works ok on it.
>
> Please tell me if you need any other information on this. Or maybe some
> workaroung exists? Some devices to turn off in UKC or sth?
>
>
> azazel [22:24:56] ~ # dmesg
> OpenBSD 3.9-stable (GENERIC) #0: Tue May 2 12:23:33 CEST 2006
> rootazazel.ostrow-wlkp.net:/usr/src/sys/arch/i386/compile/GENERIC
> cpu0: Intel Pentium II ("GenuineIntel" 686-class, 512KB L2 cache) 301 MHz
> cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,MMX
> real mem = 536453120 (523880K)
> avail mem = 482488320 (471180K)
> using 4278 buffers containing 26927104 bytes (26296K) of memory
> mainbus0 (root)
> bios0 at mainbus0: AT/286+(0e) BIOS, date 08/12/99, BIOS32 rev. 0 0xf5597
> pcibios0 at bios0: rev 2.1 0xf53b0/0x1120
> pcibios0: PCI BIOS has 8 Interrupt Routing table entries
> pcibios0: PCI Exclusive IRQs: 7 9 10 11
> pcibios0: no compatible PCI ICU found
> pcibios0: Warning, unable to fix up PCI interrupt routing
> pcibios0: PCI bus #1 is the last bus
> bios0: ROM list: 0xc0000/0x8000 0xc8000/0x600
> cpu0 at mainbus0
> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> pchb0 at pci0 dev 0 function 0 "Intel 82441FX" rev 0x02
> ami0 at pci0 dev 7 function 0 "AMI MegaRAID Series 428" rev 0x03: irq 9
> AMI 428 32b
> ami0: FW A.03.00, BIOS vA.03.00, 4MB RAM
> ami0: 3 channels, 16 targets, 1 logical drives
> scsibus0 at ami0: 1 targets
> sd0 at scsibus0 targ 0 lun 0: <AMI, Host drive #00, > SCSI2 0/direct fixed
> sd0: 20330MB, 20330 cyl, 64 head, 32 sec, 512 bytes/sec, 41635840 sec total
> ppb0 at pci0 dev 8 function 0 "DEC 21052 PCI-PCI" rev 0x02
> pci1 at ppb0 bus 1
> rl0 at pci1 dev 1 function 0 "Realtek 8139" rev 0x10: irq 11, address
> 00:02:44:7c:8c:f0
> rlphy0 at rl0 phy 0: RTL internal PHY
> xl0 at pci1 dev 2 function 0 "3Com 3c905 100Base-TX" rev 0x00: irq 7,
> address 00:60:97:4b:17:14
> nsphy0 at xl0 phy 24: DP83840 10/100 PHY, rev. 0
> fxp0 at pci1 dev 3 function 0 "Intel 8255x" rev 0x02, i82557: irq 10,
> address 00:60:b0:6c:7d:6b
> inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 0
> "Intel 82375EB EISA" rev 0x15 at pci0 dev 9 function 0 not configured
> ahc0 at pci0 dev 10 function 0 "Adaptec AIC-7880" rev 0x00: irq 11
> ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
> scsibus1 at ahc0: 16 targets
> cd0 at scsibus1 targ 5 lun 0: <TOSHIBA, CD-ROM XM-5701TA, 0787> SCSI2
> 5/cdrom removable
> ahc1 at pci0 dev 11 function 0 "Adaptec AIC-7880" rev 0x00: irq 11
> ahc1: Host Adapter Bios disabled. Using default SCSI device parameters
> scsibus2 at ahc1: 16 targets
> eisa0 at mainbus0
> eisa0: can't map I/O space for slot 14
> eisa0: can't map I/O space for slot 15
> isa0 at mainbus0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard
> vga0 at isa0 port 0x3b0/48 iomem 0xa0000/131072
> wsdisplay0 at vga0 mux 1: console (80x25, vt100 emulation), using wskbd0
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: <PC speaker>
> spkr0 at pcppi0
> npx0 at isa0 port 0xf0/16: using exception 16
> pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
> fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
> fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
> biomask fb65 netmask ffe5 ttymask ffe7
> pctr: 686-class user-level performance counters enabled
> mtrr: Pentium Pro MTRR support
> dkcsum: sd0 matches BIOS drive 0x80
> root on sd0a
> rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
>
> --
> .: Jakub G3azik
> .: zytek(at)ostrow-wlkp.net
> .: jid:zytek(at)azazel.ostrow-wlkp.net

• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]