From: Darth Lists (jt.listsdeathstar.com)
Date: Sat Apr 28 2007 - 10:10:29 CDT

• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

No. Basic 80x25 console redirection is free. You only need to pay
for the graphical interface bit. Honestly, it blows big-time
compared to a real serial console since it has a more or less useless
scroll-back buffer. I have only ever used the iLO console for the
initial installation process and the occasional visit to the ddb>
prompt when 3.7 crashed.

That said, when I installed OpenBSD on my machines here, I needed to
netboot them since the cd and floppy redirection thing was not
working too well. It's better than nothing, that's for sure, but I
would take a serial console over that any day of the week.

Cheers,

/Jason

On Apr 27, 2007, at 6:02 AM, Raimo Niskanen wrote:

> Thank you everybody for your valuable answers.
>
> Could you give me some pointers on how to use "the
> redirected console via iLO (ESC+Q)". HP documentation is
> a mess. All they want is to sell me a license for some
> Windoze application for remote management.
> Do I need a license for LO 100i something?
> And what is (ESC+Q)?
>
>
> On Thu, Apr 26, 2007 at 12:53:16PM +0200, Reyk Floeter wrote:
>> hi!
>>
>> On Thu, Apr 26, 2007 at 12:23:58PM +0200, Raimo Niskanen wrote:
>>> I have a HP ProLiant DL140 G3 coming in soon, that I really would
>>> like to run OpenBSD 4.1 on. Its predecessor runs OpenBSD (sparc).
>>> If I do not succeed it will wind up running SLES 10 and that is
>>> a pity.
>>>
>>> I have used a snapshot of OpenBSD amd64 from April 24.
>>>
>>> HP ProLiant DL 140 G2 works like a charm with OpenBSD 4.0.
>>>
>>> The problems:
>>>
>>
>> i have seen similar problems on the DL145 G3 with OpenBSD 4.0 and
>> OpenBSD 4.1.
>>
>>> 1) something with keyboard interrupts. When booting with a
>>> PS2 or USB keyboard attached BIOS, CDBOOT and boot(8) works
>>> fine, but the kernel gets no keyboard. using
>>> boot> boot cd0a:/4.1/amd64/bsd.rd -c gives an
>>> UKC> promt but does not respond to keystrokes.
>>>
>>> First changing the console using
>>> boot> set tty com0
>>> and then
>>> boot> boot cd0a:/4.1/amd64/bsd.rd -c
>>> gives a serial console that is usable. The dmsg is attached
>>>
>>
>> ukc works fine for me but the final system keyboard doesn't work. the
>> redirected console via iLO (ESC+Q) works without problems, i didn't
>> try the serial console.
>>
>>> 2) something with internal USB devices. The axe(4) driver
>>> mistakes something in the server for an USB network card
>>> and fails to configure it. Therefore the disabling of
>>> the axe device in the following dmsg output. I can live
>>> without an axe device so this is not a big problem.
>>>
>>
>> it is not an axe device, it is some internal serverworks virtual
>> stuff
>> (and i don't need it). the interesting thing is that it reports an
>> empty device and vendor id (see last line) which is not handled
>> correctly in the usb stack:
>>
>> Controller /dev/usb2:
>> addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
>> ServerWorks(0x1166), rev 1.00
>> port 1 powered
>> port 2 addr 2: full speed, power 100 mA, unconfigured, SE USB
>> Device(0x0000), ServerEngines(0x0000), rev 0.01
>>
>> the attach as axe is mostly random, it sometimes attaches as axe(4)
>> and sometimes as uberry(4) in my DL145 G3...
>>
>> uberry0 at uhub2 port 2
>> uberry0: ServerEngines SE USB Device, rev 1.10/0.01, addr 2
>> uberry0: Charging enabled
>>
>>> At the end of the dmsg there is something concerning keyboard
>>> interrupts. What can I do about it?
>>>
>>
>> we need to fix this ;)
>>
>> reyk
>
> --
>
> / Raimo Niskanen, Erlang/OTP, Ericsson AB

• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]