*******************************************************************************
* *
* This is a newly released patch... *
* *
* Online links can be found at *
* http://ftp.support.compaq.com/patches/public/unix/v5.1/cdfsdate_v51.README
*******************************************************************************

TITLE: CDFSDATE_V51 Tru64 V5.1 Date ECO Summary
 
  This README contains instructions for loading this patch, for determining
  if a kernel rebuild and system reboot are required, and for configuring
  this patch. The patch should be applied from the root process. The
  patched cdfs.mod is delivered in the patch tar file as
  /sys/BINARY/cdfs.mod.patch.

  The steps for loading and configuring the patch will differ depending
  on whether a kernel rebuild and reboot is required, and whether the
  patch is being applied to a TruCluster system.
 
  For V4.0* based cluster systems this patch must be individually
  loaded and configured on each cluster member. For V5.* based
  TruCluster systems, this patch can be loaded once, but it also
  must be configured on each cluster member.

  Loading the patch:

      Load this patch by moving the patched cdfs.mod to its proper location
      and by rebuilding /genvmunix. Use the following commands.

         # cp /sys/BINARY/cdfs.mod /sys/BINARY/cdfs.mod.pre_patch
         # mv /sys/BINARY/cdfs.mod.patch /sys/BINARY/cdfs.mod
         # chown bin.bin /sys/BINARY/cdfs.mod
         # chmod 644 /sys/BINARY/cdfs.mod

      Rebuild /genvmunix.

         # doconfig -a -c GENERIC
         # cp /sys/GENERIC/vmunix /genvmunix

      Note, time can be saved on cluster systems by performing the
      /genvmunix rebuild once and copying the resulting /genvmunix to
      each cluster member.

      The loading portion of this patch is now complete.
   
  This patch can be applied to a running system and the corrected behavior
  will take effect immediately. However depending on how the /vmunix
  kernel is configured, it may be necessary to rebuild a new /vmunix
  kernel and to reboot the system to have the patch be permanent.
  
  Determining if a kernel rebuild is required:

      To determine if a kernel rebuild is required, perform the following
      command.

         # nm /vmunix | grep -c cdfs_tounixdate

      If the output is a '0', then a /vmunix kernel rebuild and system
      reboot is not required. Proceed to OPTION 2.
    
      If the output is a '1', then the a /vmunix kernel rebuild and
      system reboot will be required to make the patch permanent.
      Proceed to OPTION 3.

      For the most direct method of installing this patch, proceed to
      OPTION 1.

    
  OPTION 1: The most direct method to install this patch.
  
      The most direct method for installing this patch is to rebuild
      /vmunix and reboot. Here are the steps:
   
         Rebuild /vmunix. Use doconfig with the -c option and specify
         the existing config file name. The config file name is usually
         the name of the system, in uppercase letters.
       
            # doconfig -c <config-file-name>
         
         When the doconfig command completes, it will list a vmunix
         file that must be copied to /vmunix.
       
         Reboot the system.

         The patch is now permanently installed.
       

  OPTION 2: Installing this patch when a kernel rebuild and reboot is
            not required.
          
      This option shows how to install the patch on a system where a
      kernel rebuild and reboot is not required for the patch to be
      permanently applied.
     
      Prepare to load the patch:
  
         Loading the patch first requires that all cdfs file systems
         are unmounted and the cdfs kernel option is unconfigured.
  
         First unmount all cdfs file systems.
     
            # umount -Av -t cdfs
      
         Verify all cdfs file systems have been unmounted. The output
         of the following mount command should not show any file
         systems still mounted.
  
            # mount -e -t cdfs
      
         Second, unconfigure the cdfs kernel subsystem, making sure
         it was first configured.
    
            # sysconfig -c cdfs >> /tmp/cdfs_patch.out
            # sysconfig -u cdfs >> /tmp/cdfs_patch.out
      
         Configure the patch with the following command:
     
            # sysconfig -c cdfs
       
         The patch is now installed on the running kernel.
 
 
 OPTION 3: Installing the patch on a system where a kernel rebuild
            and reboot are required.
          
      This option shows how to install the patch on a system where a
      kernel rebuild and reboot is required for the patch to be
      permanently applied.

      If the system can be rebooted immediately, then proceed to
      OPTION 1.
     
      If the system cannot be rebooted immediately but the corrected
      behavior from the patch is needed and a planned reboot will occur
      at a later time, then:
     
         Perform OPTION 2 to have the patch applied to the running system.

         At the time of the next reboot, run doconfig to generate
         a new /vmunix kernel and reboot the system. Use doconfig
         with the -c option and specify the existing config file name.
         The config file name is usually the name of the system, in
         uppercase letters.
       
            # doconfig -c <config-file-name>

      The patch is permanently installed once the new kernel is copied
      to /vmunix and the system is rebooted.
     
      ** Note **:
      Do not copy the new rebuilt kernel to /vmunix until the system is
      ready to be rebooted.
      

---

• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]